Peugeot 3008 Key Fob Problems
The mid-sized SUV from Peugeot, the 3008, has many positive attributes. It looks smart, drives well and comes with a large boot. Can it compete in the most crowded segment of the market perhaps?
If your Peugeot key fob isn’t working, it may have been exposed to clean tap water or soapy water. You may need to remove the battery and clean it using electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs include an insignificant coin battery that powers their remote locking and other functions. This battery is a bit dated and wears out after years of use. An easy way to determine whether the battery is in good condition is to conduct a voltage test. Multimeters are used to measure voltage between the poles that are plus and minus of the battery. The results of this test will tell you whether the battery is dead or near Me not.
If you’ve been using your Peugeot 3008 for a while and the key fobs have stopped working, there could be an issue with the receiver module. The receiver module is responsible for capturing radio frequency signals from key fobs and transferring signals to the car’s systems. If the receiver module is faulty, it will not be able to relay commands to the other modules in the vehicle.
Moisture or sweat that gets on the circuit board is another frequent cause of an unworking key fob. This can lead to short circuits, which will drain the battery and stop the feature that locks the fob’s remote. If this is the case then you must bring your key fob to a chip level technician to repair it.
Water damage
If you dropped your key fob in the pool, threw it into the wash or even left it in the rain for too long, water damage could be a real problem. Water is a great conductor and can quickly short out parts of the circuit board. It can also cause rusting of the metal traces as well as other components of the key fob. A wet circuit may cause the battery to lose charge.
If you have an additional key fob, use it to unlock and lock the Peugeot 3008 in order to determine if a dead coin-cell battery as the cause of the issue. Interference signals can cause your key fob not to function properly. They interfere with the signals sent by the receiver module. These interference signals are triggered by a variety of sources such as radio transmitters in the vicinity.
If you notice sloshing sounds coming from inside your Peugeot 3008 while driving, it’s likely due to a clogged condensate drain of the evaporator. You can test this by blowing compressed air through the drain holes beneath your door. You can also use flexible metal wire for wriggling drain holes to get rid of any dirt that has collected. Air pockets can be detected by sloshing noises.
Faulty receiver module
The receiver module on the Peugeot 3008 key fob is responsible for transferring the remote keyless system signal from the key fob to the car’s receiver. This module could be damaged and block the car from acknowledging your key fob. This problem can also be caused by an inactive battery or water damage. Also, interference from electronic devices operating at the same frequency. In these cases the message “card not detected” may be displayed on the display.
Luckily, there are a number of ways to fix this problem. You might try replacing the battery or reprogramming the key fob. You can also start the vehicle with a spare key. If the key fob doesn’t work after following all these steps, then it could be a problem with the chip.
The best way to know whether your key fob has damaged chip is to take it off and clean it up with a paper towel and rub alcohol. If the chip is damaged it is recommended to purchase a new one. The FB Series enclosures come with the battery holder for coins, which fits the most commonly used types of key fob batteries. They can also be customized by using digital printing and CNC machined cutouts. If your key fob has been exposed to salty or dirty tap water, the chip may be contaminated and need to be cleaned.
A malfunctioning keyless entry system
If you see “card not detected”, this signifies that your car cannot receive a signal sent by your key fob. This could be due to many reasons, including the battery being weak or dead. The problem can often be solved by pressing the start button on the key fob. In some cases however, you may need to take the key fob to a peugeot key fob repair dealership for additional repairs.
Checking the battery is the first step to solving the issue with a Peugeot 3008 keyfob that doesn’t unlock or lock doors. Batteries are typically the cause of malfunctioning keys. However there are other reasons that could be at play. This includes worn buttons, water damage, receiver module problems, and signal interference.
If you’ve recently had your Peugeot key fob exposed to clean tap water, it’s a good idea to remove the battery and dry the electronic components with paper towel. You can also employ a cleaner or isopropyl ethanol to do this. If the fob has been exposed to soapy or salty water, it’s best to replace it.
If your key fob isn’t working You can reset it by removing the battery with 12 volts for 15 minutes. Connect the negative cable, then the positive cable.
